On this page down the page you'll find additional excellent information and facts on the subject of How to Install a Bathtub.
Installing a bathtub isn't precisely rocket science, but it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily easily accessible, the task can relocate quickly; if you have to open a wall to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub as well as set in the brand-new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed job, it is much better to think about utilizing one prior to you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your bathroom if you have already bought a brand-new bathtub and also do not require to alter the plan of your previous water system pipes.
Your tools and material checklist should consist of the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted gain access to that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub until the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water and also inspect all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the tub as well as likewise examine the overflow electrical outlet and the normal outlet for leaks.
Ultimately, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has been used at the very least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous type should be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and fittings. They are offered in tubes and cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very fascinated with How to Install a Bathtub Yourself and I am assuming you appreciated my page. Those who enjoyed our blog posting plz don't forget to share it. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Visit My Website